News of x-sim

Hi all and thanks in advance for any advice.

I am just about to upgrade my motors and purchase a pair of SCN6's 50kgf with 150mm travel. The million dollar question is do I order npn or pnp IO type. I already own a very good 10a 24v Calex PSU which should be man enough for both motors and was planning on buying some RS485 to USB adapters.

So back to the question, pnp or ...

Good Afternoon !

I know there are the RealFeel plugin to handle the forces of the suspension arm to apply directly on the steering wheel of the car, I was wondering if there is any way to get information is the value of this force through the serial port, the same way that today l receive strength G lateral and longintudinal by x-sim Converter, is there any manual way to do it ? I used ...

A ver, he buscado y no encuentro nada q me aclare el tema al 100%. He visto muchos 2dof y cada uno tiene unas medidas y configuraciones de posiciones ¿como calculais el tamaño optimo de las bielas? Y la posición de los motores? Unos lo ponen debajo, otros mas lejos, algunos tienden a incluso a empujar desde los laterales... Entiendo tambien q la fuerza de los motores que tengas influye, pero no tengo clara la ...

Hallo Leute,

ich stelle mich erstmal vor. Ich heiße Waldemar, komme aus Hannover und studiere Maschinenbau.
Dank meines verrückten Interesses an Technik bin ich auf dieses Forum gestoßen und schon dabei
mir ebenfalls ein Seatmover zu basteln. Hab hier auch schon netten Support von dem einen
oder anderen Forummitglied bekommen und konnte auch mal ein Rig Probefahren. Für diese Hilfestellung
kann ich nur DAumen hoch sagen und bin begeistert.

So nun zu meinem Problem, ich ...

I have 6 Canimex 60:1 worm gear crank arm gearboxes for sale. These are used surplus and were purchased for a 6 DOF platform and never used.
Here are the specs:
Ratio – 60:1
Dual Shaft
Size – 50 (means 50mm distance between input and output shaft)
Shaft Size: input shaft – 5/8”, output shaft – 3/4”
Crank Arm: Center to Center distance: 73mm
Uses 90 weight gear oil
Bearings: input shaft bearing – 6203, ...

Finally finished my flight simulator project which was started four years ago. I started with the purchased Joyrider build plan online. Started purchasing PVC tubing, nuts and bolts and all the necessarry hardware. Finished the build with no motors. Motion was on a gymbal system utilizing center of gravity of the rider. I wasn't satisfied with it and dreamed of having motors and interface but didn't know where to start. Then, I stumbled across this ...

Buenas a todos,
mi simulador ha echado a andar pero como novato tengo dos preguntas que hacer:
- conecto las dos jrk´s a una batería pero tengo una duda, ¿puedo juntar los positivos por un lado y los negativos por otro y conectarlos a los bornes?, si no es así ¿Cómo debo hacerlo?
- he probado cada motor por separado y me parece que la tarjeta se calienta mucho, mucho es difícil de definir pero ...

I have connect a 3v-36V Dual 15A H-Bridge DC Motor Driver on my arduino as follows...
Ard 5v <> Bridge 5+
Ard Gnd <> Bridge Gnd
Ard PWM1 <> Bridge PWM1
Ard PWM2 <> Bridge DIR1
Bridge Power <> 12v 16A Input PSU
Bridge Ground <> PSU Ground
Bridge Motor1 <> Servo1
Bridge Motor1 <> Servo1

The problem is that when i power up the circuit, the bridge sends the 12v directly to the motor ...

ciao a tutti, da qualche tempo seguo il forum con interesse per la realizzazione di un simulatore. Ho deciso di realizzarne uno con i due motorini, il progetto è a buon punto , sono in attesa che arrivino i pezzi di elettronica per poter assemblare il tutto ! ho provveduto a reperire il materiale e porre alcune modifiche nella scelta dei materiali della struttura, realizzandola in legno ! il sistema dei motorini è su un ...

if anybody needs it... no limits 2 update 2.0.8.0 memory driver