News of Converter questions

Hi all, can anyone tell me please if there is a way of start/stop the converter with a key? the only way of doing it is with the mouse?

I am using it with one computer only so every time I need to run the simulator I need to go to desktop to press "start" and is giving me problems with the games after I go back to play.

Thanks.

Hello,

I am using a K8061 with sabertooth 2x12 and wiper motor combined with potentiometers.

When starting and closing Converter, the default value on outputs is 0%, in my case this mean full speed in negative direction !
If I forgot to shutdown my motors (before starting and quitting Converter) they will turn non stop and I have to calibrate the potentiometers...

Is there a way to set output value to 50% by default when ...

I am about to set this 3dof up but dont know how exactly :)
I have my old AMC 1.5 and now one Arduino Uno to use together. My two DSMHB's are wonking fine aswell.

Well I am not sure what to do on the USO setup :?

Please I apreciate any clues.

By the way I dont have ...

two k8055 walleman...I can switch them around Nr 0 Nr 1 xsim reads both but only send to one...
it sees both card at the profiler...press START AND ONLY ONE CARD WILL OUTPUT the other does not output...
and will freeze up....:( if I run one card at the time will work...k8055 demo runs both no problems..x-sim and k8055d.dll updated 5.0.0.0...installed in syswow and system 32 (My ...

Hello to all

I have a problem with the latest version of x-sim 3.0.1.8 beta aluminum.
In practice starts once only and then the converter continues to load but will not start and gives me this error ....



What can I tried to reinstall and restart the pc but the same does not go ....

Hello
x-sim 3.0.1.4 and 3.0.1.5 do not recognize my scn5?
the 3.0.0.7 release no probleme
thank you not to answer

Hi guys,

I cant seem to figure out what i'm doing wrong.. all i can get when pressing start is error connecting to com port.

I attached a screenshot of what i have. I'm not sure why i have to use com11 when the laptop only has 4 comports, but it seems to work connecting the arduino with other programs, just not this one.

Hi everybody,
I'm trying to use x-sim with arduino... https://github.com/X-Sim/X-PID-Arduino-PID-motor-control
I can see my connected arduino on x-sim converter program and i can edit configurations...
I create two axis and connect them to arduino....
But when i'm pressing to 'START' i'm getting an error "Error opening comport COM1"

Hi Sir

Would you please consider creating a plugin for the new Kangaroo x2 and Sabertooth Driver using packeritised serial interface,

attachment of manual etc in this thread

http://www.x-sim.de/forum/viewtopic.php?f=43&t=867#p7441

I have 24 volt 27 amp run, 590 watt motor wormgear units, I intend to build a 2 dof to start, then I hope to build a 6 dof, using the 2 x 60 sabertooth.

Have tried the cheap china drivers and fried a few in ...

Hi all, I'm thinking about the following scenario:

Using a Tablet PC for "simulator PC Control" with the X-Sim CONVERTER. The tablet model is Samsung TAB P8510 ATIV RT installed with Windows 8.
http://www.samsung.com/es/consumer/mobile-phone/tablets/ativ-tab/GT-P8510MSAPHE-spec

Will it work well on X-Sim Converter on this device?
Will X-Sim Converter with Windows 8?

Has anyone experienced using Tablet PC?


Greetings and thanks in advance