It is currently Thu 23. Oct 2025, 23:20

News News of Converter questions

Site map of Converter questions » Forum : Converter questions

Open a thread for a question about the simulator control software.
If you cannot receive any data in the input setup use the upper two forums!

How to map stop button to our wheel button?

Hi guys or Dave ,
Hi guys when I am racing n happily enjoying xsim, suddenly someone bang my car n cause me to crash and roll n suddenly my motion chair rock so violently till I felt dangerous. I don't have the emergency power stop button. Hence if I can map the converter stop button to my wheel button it would be great. Do we need to write a script for it or a ...
Read more : How to map stop button to our wheel button? | Views : 2454 | Replies : 2


Com Port Errors, JRK, XSim3, PC?

I am running 2 JRKs via Xsim 3. Unfortunately I am getting Com Port Errors on the PC running converter that drives the JRKs.
I am not sure if the error is caused from Xsim, JRKs, or my PC.
Has anyone had any similar issues.
Any advice is appreciated.
Sim is running great except for this little glitch.
Read more : Com Port Errors, JRK, XSim3, PC? | Views : 40369 | Replies : 52


Slider - How to use?

I have been playing around with "Xsim3 converter" for a while now and I can't seem to get the sliders to change any values. I have assigned the slider by right clicking the math line, but the output value does not change when I move the slider. I must be doing something wrong.
Any help please.

Thanks
Read more : Slider - How to use? | Views : 3497 | Replies : 5


Can't get lateral movement with xsim2

Hi guys,
I am being told I can post xsim2 software questions here also so that everyone start to do this and we make this website popular! I am using xsim for iracing only..so far I am loving xsim software in terms of movement after hard time of leaning how to use...3 full days to be exact! .but no matter how I increase the lateral force the no. Value (actually it is lowering the no. ...
Read more : Can't get lateral movement with xsim2 | Views : 6952 | Replies : 10


USO Befehle für Pololu Interface

Hallo,
ich habe mir für die ersten Gehversuche ein Pololu Servoboard von Robotikhardware bestellt und wollte mal fragen ob jemand bereits Parameter für die USO Schnittstelle erarbeitet hat. Leider habe ich keinen Beitrag zu diesem Thema gefunden bis jetzt. Danke für die Starthilfe.
Read more : USO Befehle für Pololu Interface | Views : 23787 | Replies : 7


Doubts at the initial configuration. / Duvidas com a configu

Please, I'm having problems with the initial configuration of the X-Sim 3.0.0.6.

What can this be? :?:
The configuarações are equal to the old X-SIM2 and work well on it.

hugs
Everton

imagem.JPG


Por favor, estou tendo problemas com a configuração inicial do X-Sim 3.0.0.6.

O que pode ser isso? :?:
As configuarações estão iguais ...
Read more : Doubts at the initial configuration. / Duvidas com a configu | Views : 5944 | Replies : 15


Arduino uno stepper rev meter issue

Hi to all.
I'm a new italian user, so sorry for my english. I've found this great forum searching for build a simple rpm meter for my sim, and after viewing other user post i realize my first project. The platform is an arduino uno connected to an h bridge to drive a small stepper motor from real car cluster( a clone of switec x25). I,'m using x-sim 3. The bound rate is setting to ...
Read more : Arduino uno stepper rev meter issue | Views : 4027 | Replies : 5


How to reset axis maximum when converter is not on?

Is it possible to have an axis that will reset its maximum value to something (could be any low number, like 1) whenever the converter is started? I have an axis for maximum RPM that has automatic maximum adjustment in Output 1:1. I have a shift light that starts blinking at 90% maximum rpm. So when I fully rev on neutral before I start driving, the value gets set to the maximum RPM value.

It ...
Read more : How to reset axis maximum when converter is not on? | Views : 2581 | Replies : 2


k8055..sabertooth..wipers

I keep getting errors and the k8055 is not reconised by the x-sim converter.I am using x-sim 3.0.0.4

converter page error 2.jpg


there is no IP address or anything in all oupput of found devices other than base shaker and i don't know where that came from.

Also when i hook the usb cable into the k8055 and computer i get this windows message

converter error 3.jpg
...
Read more : k8055..sabertooth..wipers | Views : 2784 | Replies : 3


Question to SirNoName Question to SirNoName

Hi Sirnoname!
I wish you could make one executable tool or anything that could help me to set the core 0 (zero) to back to all programs after I exit the converter.
What I mean is that I always have to restart my system or I have to CTRL alt del and change it manually to use 3ds max or other heavy core demanding software.
I think the most obvious way would be it automaticaly ...
Read more : Question to SirNoName | Views : 4937 | Replies : 8


 

Login  •  Register


Statistics

Total posts 23561 • Total topics 3142 • Total members 4075